Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
ppc-osx-on-qemu-for-osx [2018/06/20 12:01] – [Qemu installation] cat_7 | ppc-osx-on-qemu-for-osx [2018/09/11 02:18] – [Experimental builds] cat_7 | ||
---|---|---|---|
Line 13: | Line 13: | ||
Installations of other versions of Mac OS or OSX (roughly) follow the same path. \\ | Installations of other versions of Mac OS or OSX (roughly) follow the same path. \\ | ||
+ | |||
+ | If you need to boot from a real CD, see the section Booting from a real CD below. \\ | ||
==== Qemu installation ==== | ==== Qemu installation ==== | ||
Line 51: | Line 53: | ||
(*)The mac model entry accepts 3 options for the via parameter: \\ | (*)The mac model entry accepts 3 options for the via parameter: \\ | ||
- | mac99, | + | mac99, |
mac99, | mac99, | ||
- | mac99, | + | mac99, |
* Double-click qemu.command. This starts Qemu and boots the MacOS9.2.iso installation CD image. | * Double-click qemu.command. This starts Qemu and boots the MacOS9.2.iso installation CD image. | ||
Line 99: | Line 101: | ||
However, you can also use the realtek 8139 device. This requires installation of the appropriate drivers. You can download them from the [[http:// | However, you can also use the realtek 8139 device. This requires installation of the appropriate drivers. You can download them from the [[http:// | ||
- | There are two ways to get networking going in OSX: through slirp or tap networking | + | There are two ways to get networking going in OSX: through slirp or tap networking: |
=== Slirp-based networking === | === Slirp-based networking === | ||
Line 130: | Line 132: | ||
- | === Running two qemu instances with networking=== | + | === Running two qemu instances with networking === |
If you want to run two installations of Mac OS/OSX, Qemu needs to be able to tell the network devices apart. You can add a mac address to the networking device: | If you want to run two installations of Mac OS/OSX, Qemu needs to be able to tell the network devices apart. You can add a mac address to the networking device: | ||
Line 138: | Line 140: | ||
* -netdev user, | * -netdev user, | ||
Please note that adding a mac address other than the default to the network device leads to the discovery of a new network card in OSX. You need to configure that card through the network preferences. | Please note that adding a mac address other than the default to the network device leads to the discovery of a new network card in OSX. You need to configure that card through the network preferences. | ||
+ | |||
+ | === Getting files in and out of your emulated Mac through a network connection === | ||
+ | |||
+ | OSX 10.3/10.4 guests: Make sure you have file sharing enabled on your host and that you share some folder. Find the current IP address of your host: open the system report and click Networking. The IP address should show behind the active network connection. \\ | ||
+ | Start Qemu, click Go/Connect to server. Enter | ||
+ | afp:// | ||
+ | At Connect as select Registered user and enter your user name and password for your host. Then select a shared folder from the list and click OK. You can now read and write files to the shared folder that appeared on your desktop.\\ | ||
+ | |||
+ | ==== Booting from a real CD ==== | ||
+ | |||
+ | To boot from a real CD, you first need to insert the CD and unmount it using e.g., Diskutility. \\ | ||
+ | Next, run Qemu as root. So add sudo in front of ./ | ||
+ | Example command line:\\ | ||
+ | |||
+ | #!/bin/bash | ||
+ | cd " | ||
+ | sudo ./ | ||
+ | |||
+ | |||
+ | If the CD was not unmounted correctly, Qemu tells you the commands you need to enter (in e.g., another terminal window) to unmount the CD. For example:\\ | ||
+ | |||
+ | qemu-system-ppc: | ||
+ | qemu-system-ppc: | ||
+ | qemu-system-ppc: | ||
+ | |||
+ | |||
+ | The CD might stay unmounted after you stop Qemu. You can use diskutility to mount it again and eject it. Or use the terminal command Qemu suggests for mounting the CD. \\ | ||
+ | |||
==== Creating new disk image in OSX with DiskUtility ==== | ==== Creating new disk image in OSX with DiskUtility ==== | ||
Line 156: | Line 186: | ||
+ | ==== Changing the mounted cdrom image ==== | ||
+ | |||
+ | In Mac OS guest: First drag any mounted CD from the desktop into the trash. | ||
+ | |||
+ | Open the Qemu Monitor by selecting View/Compat monitor from the Qemu menu \\ | ||
+ | Type “info block” to find the name of the CD drive in Qemu (most likely: ide1-cd0) \\ | ||
+ | Type “eject ide1-cd0” \\ | ||
+ | Type “change ide1-cd0 / | ||
+ | Close the Qemu Monitor by selecting View/VGA \\ | ||
+ | |||
+ | ==== Mounting a real cd ==== | ||
+ | |||
+ | NOTE: you need to unmount the real cd from the desktop (using e.g., disk utility) before using it in Qemu. \\ | ||
+ | Open the Qemu Monitor by selecting View/Compat monitor from the Qemu menu \\ | ||
+ | Type “info block” to find the name of the CD drive in Qemu (most likely: ide1-cd0) \\ | ||
+ | Type “change ide1-cd0 / | ||
+ | Close the Qemu Monitor by selecting View/VGA from the Qemu menu \\ | ||
Line 167: | Line 214: | ||
-Sound support\\ | -Sound support\\ | ||
- | -Support for a PMU (power management unit)\\ | ||
You can download some of these experimental builds from our forum: http:// | You can download some of these experimental builds from our forum: http:// |