Emaculation.com

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
sheepshaver_online_guide [2010/02/11 18:15] – clockwisesheepshaver_online_guide [2020/09/26 04:13] (current) – clockwise
Line 1: Line 1:
 ====== Getting online in SheepShaver for Windows ====== ====== Getting online in SheepShaver for Windows ======
  
-(Updated September 17, 2009)+(Updated September 26, 2020)
  
 ===== Introduction =====  ===== Introduction ===== 
 +**Note**: This guide was written for SheepShaver, but you can use the exact same instructions to get online in Basilisk II.
 +
 It's been my experience that going online in SheepShaver for Windows using the "Basilisk II Router" method as described in [[basilisk ii online guide|this guide]] doesn't work.  I'm not sure why.  One method that //does// work, however, is using the "Basilisk II Slirp" method.  Here's how to do it: It's been my experience that going online in SheepShaver for Windows using the "Basilisk II Router" method as described in [[basilisk ii online guide|this guide]] doesn't work.  I'm not sure why.  One method that //does// work, however, is using the "Basilisk II Slirp" method.  Here's how to do it:
 ===== Setting up the GUI ===== ===== Setting up the GUI =====
 Open the SheepShaver GUI.  Browse to the "Network" tab and select "Basilisk II Slirp" from the drop-down menu.  See figure one, below. Open the SheepShaver GUI.  Browse to the "Network" tab and select "Basilisk II Slirp" from the drop-down menu.  See figure one, below.
  
-{{http://www.emaculation.com/sheepshaver/sheepshaveronline1.jpg}}\\ +{{https://www.emaculation.com/sheepshaver/sheepshaveronline1.jpg}}\\ 
 **Figure 1: The SheepShaver GUI** **Figure 1: The SheepShaver GUI**
  
 ===== Setting up TCP/IP ===== ===== Setting up TCP/IP =====
  
-Launch the emulator.  Locate the "TCP/IP" control panel in your system directory.  Set it up using the same values as in figure two, below:+Launch the emulator.  Locate the "TCP/IP" control panel in your system directory.  Set it up using the same values as in figure two, below.
  
-{{http://www.emaculation.com/sheepshaver/sheepshaveronline2.jpg}}\\ +Note that if you are using System 7.5.3 or 7.5.5 you might not have a TCP/IP control panel.  In this case go to the "Apple Extras" directory and run "Network Software Selector". Select "Use Open Transport Networking" and you should be given a TCP/IP control panel **after a reboot**. 
 + 
 +{{https://www.emaculation.com/sheepshaver/sheepshaveronline2.jpg}}\\ 
 **Figure 2: Use these settings in your TCP/IP control panel** **Figure 2: Use these settings in your TCP/IP control panel**
  
Line 23: Line 27:
  
 [[http://www.icab.de/dl.php|iCab 3.0.5]] is also quite good (but not as stable as Classilla). [[http://www.icab.de/dl.php|iCab 3.0.5]] is also quite good (but not as stable as Classilla).
 +
 +If you are using Basilisk II, you are almost required to use [[http://www.icab.de/download.html|iCab 2.9.9 68k]] now.  Anything else will likely crash the emulator.